型號 | Machine Type | HL-90SE | ||||||
國際型號 |
|
900-140 | 900-230 | |||||
A.射出系統 | Injection Unit Code | 140 | 230 | |||||
螺桿代號 | Screw size | A | B | C | D | E | F | |
01. 螺桿直徑 | Screw diameter | mm | 25 | 30 | 32 | 32 | 35 | 40 |
02. 射出量 | Injection capacity-PS | Oz. | 1.9 | 2.7 | 3.1 | 3.9 | 4.7 | 6.1 |
gm | 54 | 78 | 89 | 111 | 133 | 173 | ||
03. 螺桿長徑比 | Screw length to diameter ratio | L/D | 24 | 20 | 18.8 | 21.8 | 20 | 17.5 |
04. 最大射出壓力 | Injectilon pressure | Kg/cm2 | 2829 | 1964 | 1727 | 2324 | 1943 | 1488 |
05. 射出行程 | Injection stroke | mm | 120 | 150 | ||||
06. 理論射出容積 | Calculated injection volume | cm3 | 59 | 85 | 97 | 121 | 144 | 188 |
07. 理論塑化能力 | Plasticizing rate | Kg/hr | 20 | 35 | 43 | 34 | 53 | 73 |
08. 射出率 | Injection rate | mm/sec | 163 | 120 | ||||
cm3 /sec | 80 | 115 | 131 | 97 | 115 | 150 | ||
09. 螺桿轉速 | Screw speed | Rpm | 320 | 267 | ||||
10. 噴嘴封閉力 | Nozzle force | Ton | 7.4 | 7.4 | ||||
11. 電熱加熱功率 | Heating input power | Kw | 5.5 | 6.3 | ||||
12. 料管加熱段數 | Barre heating zines | No. | 3+2 | |||||
B. 開合模系統 | Clamping Unit | |||||||
13. 鎖模力 | Clamping force | Ton(Kn) | 90(882) | |||||
14. 最大開模行程 | Mold opening stroke | mm | 300 | |||||
15. 模板全開距離 | Open daylight | mm | 660 | |||||
16. 容模尺寸 | Die-height available | mm | 150-360 | |||||
17. 模板尺寸 | Size of platens H×V | mm×mm | 590×590 | |||||
18. 柱內尺寸 | Space between tie-bars | mm×mm | 410×410 | |||||
20. 頂出力 | Ejector force | Ton | 5.4 | |||||
21. 頂出行程 | Ejector stroke | mm | 80 | |||||
C. 其他 | General | |||||||
22. 電機功率 | Pump motor power | Kw(Hp) | 11(15) | |||||
23. 系統最高壓力 | Hydraulic system pressure | Kg/cm2 | 170 | |||||
24. 機器總功率 | Total installed power | Kw | 16.5 | 17.3 | ||||
25. 油箱容量 | Oil tank capacity | Litre | 250 | |||||
26. 機器重量(約) | Total machine weight(approx) | Kg | 3600 | 3700 | ||||
27. 機器尺寸 | Machine dimensions L×w×h | m×m×m | 4.2×1.2×1.9 |